Keystone Termination Tool
Dedicated pressing tool for the Cablenet range of Keystone Jacks
Terminates and cuts all 4 pairs in a single operation
Excess wires are automatically cropped
Fast, reliable and repeatable terminations
Simple to use
Ergonomic design of handles enhances productivity
Compatible with Cablenet Cat5e, Cat6 and Cat6A keystone jacks
Replacement termination heads available
Krone Style 2A Punch Down Tool
A Krone style punch down tool is a small hand tool used by telecommunication and network technicians. It is used for inserting wire into insulation-displacement connectors (IDC) on punch down blocks, patch panels, keystone modules, and surface mount boxes (also known as biscuit jacks).
The Krone style punch down tool features a scissor action cable trimmer which activates during the punch down process.
This tool also features a fold out individual wire removal hook.
Comfort Tool for Keystone Jacks
Screw down holder for Keystone Jacks
This holder is deigned to be screwed to a workbench or similar to aid termination
110 Impact Punch Down Tool
A 110 punch down tool is a small hand tool used by telecommunication and network technicians. It is used for inserting wire into insulation-displacement connectors (IDC) on punch down blocks, patch panels, keystone modules, and surface mount boxes (also known as biscuit jacks).
Termination pressure can be adjusted from low to high depending on the termination requirement
Replacement blades are available - 87-0439
RJ10, RJ11, RJ12, RJ45 Non-Ratchet Crimp Tool
This non-ratchet crimp tool is suitable for RJ45 (8P8C), RJ12 (6P6C), RJ11 (6P4C), 4P4C & 4P2C Crimp Plugs.
This crimp tool also features a wire cutter and wire stripper and is manufactured from black carbon steel with plastic covered handles.
Termination is really simple, insert plug and trimmed cable then squeeze the handles to crimp the plug on to the cable and simply release once done.
BT/RJ11 Rachet Crimp Tool
All-in-one modular non-ratchet crimping tool.
This non-ratchet crimp tool is suitable for RJ12 (6P6C), RJ11 (6P4C) and 6 position British plug (BT style).
This crimp tool also features a wire cutter and wire stripper for flat and round cable and is manufactured from black carbon steel with ergonomic plastic covered handles.
RJ45/RJ11 Ratchet Crimp Tool
Modular ratchet crimping tool.
This ratchet crimp tool is suitable for RJ45 (8P8C), RJ12 (6P6C), RJ11 (6P4C).
This crimp tool also features a wire cutter and wire stripper for flat and round cable and is manufactured from black carbon steel with ergonomic plastic covered handles.
RJ45 Crimp Tool for use with 22-2096
This high quality RJ45 crimp tool is designed solely to crimp the 22-2096 Cat6a RJ45 Large OD Crimp Plugs
In addition to the RJ45 crimp function, it also incorporates a simple cable cutter and stripping attachment.
Universal Cable Stripping Tool up to 22Awg
This Universal Cable Stripper/Cutter is suitable for stripping round cable, flat wire, stranded wire and multi-conductor cable between 3mm and 9mm (UTP, FTP & STP).
Cable Stripper for UTP/STP
Specifically designed to inexpensively quickly measure, strip and cut UTP and STP/FTP cables.
Easy to use and economical, this handy disposable cable stripper includes a 110/88 type punch tip.
For RJ11 and RJ45 unshielded twisted pair wiring.
Cable diameter range - 5.00mm to 6.2mm
RJ45/RJ11/BNC/USB Continuity Tester
The Multi-protocol Cable Tester is a Remote Cable Tester, palm sized unit with four types of connector: RJ45, RJ11, USB and BNC.
This unit can be used to verify the condition of cables both before and after their installation. The separate passive module is connected to the remote end of the installed cabling.
Easy operation - simply press the button.
Multiple LEDs give a clear indication of the following:
Open/short wiring,
Connected wires,
No connection/no terminator,
Wrong connection/non-parallel connection.
USB Ports: The Master Unit has a USB Series B connector and the Remote module has a Series A connector.
RJ45 Continuity Tester
The Cablenet RJ45 Continuity tester is a device that transmits an electrical signal through each of the wires in a copper twisted pair cable to determine if it is connected to the correct pin at the other end.
Can be used to test installed cabling or individual patch leads
Can be used to test the shielding continuity on FTP cabling
Compact and easy to carry
Easy to verify cable continuity - Open, Short or Misswire
Can test RJ45, RJ11 and RJ12
Jacket Stripper 4.0-11.0mm Diameter
Strip UTP/FTP/STP, multicore and fibre optic cables quickly and efficiently with the Cyclops cable stripper. Works with cables up to 12mm in diameter.
Simply place the cable into the Cyclops Cable Stripper, rotate once in one direction for cables with thin insulation or once in the opposite direction for cables with thicker insulation, remove the tool and pull off the insulation.
No adjustment required.
Replacement head for Maxxam Keystone Tool
Replacement termination head for the Maxxam XX6A0030 termination tool
110 Impact Punch Down Tool
A 110 punch down tool is a small hand tool used by telecommunication and network technicians. It is used for inserting wire into insulation-displacement connectors (IDC) on punch down blocks, patch panels, keystone modules, and surface mount boxes (also known as biscuit jacks).
Termination pressure can be adjusted from low to high depending on the termination requirement
Replacement blades are available - 87-0439
Krone Style Punch Down Tool
A Krone style punch down tool is a small hand tool used by telecommunication and network technicians.
It is used for inserting wire into insulation-displacement connectors (IDC) on punch down blocks, patch panels, keystone modules, and surface mount boxes (also known as biscuit jacks).
The Krone style punch down tool features a scissor action cable trimmer which activates during the punch down process.
This tool also features a fold out individual wire removal hook.
To see prices and order this product, please Log In or Call us on 01276 405 300